How to correctly install CO2 laser engraving and cutting machine?

This is a key point: the CO2 laser machine will work well only if you install the CO2 laser engraving and cutting machine correctly. Do not worry; this article will help you to know the correct installation process of the CO2 laser engraving and cutting machine. Let’s go with the following steps to install a CO2 laser machine:

Step 1

Remove the whole package; recover the machine such as wood, plastic film, etc. Be careful with of the nails.

Step 2

Now open the front door, the side door and remove all additional parts of the machine, such as water cooler, dust collector, air pump, laser tube, rotary etc. Please cut the tie on the X-axis belt and Y axis after opening the front door, get the CD and then move the laser head to the center of the work area by hand.

Step 3

The most vital step to install correctly a CO2 laser machine is to install the CO2 laser tube. Remove the laser tube from the package leisurely, and then put it in the socket of the laser tube on the back of the machine. If the laser tube has a protective plastic cover, cover the protective tape. If not, please cover enough waterproof tape. In the laser light, there is water behind the high-pressure end is water.

Step 4

Water cooler installation:  connect the water inlet and the water outlet of the water cooler with the water outlet and the water inlet of the machine by means of the silicone tube and then connect the air plugs.

Step 5

Installation of the air pump: connect the air outlet of the air pump with the air inlet of the laser cutting.

Step 6

The method of installation of the dust collector: connect the tire port of the dust collector with the telescopic tube of the laser machine.

Step 7

The installation of the floor: connect the security of the floor, find a cable and you must connect the machine to the floor. The other end connects the steel bar; it should be buried under the ground 1.5 meters. If it is in the humid place, the depth of the burial can be shallow.

Step 8

CO2 laser cutter should use the power with the 220V. If your local power is 220V, you can directly connect it. If not, you require an additional power transformer for the machine to change the power.

Step 9

First, supply power to the water cooler. Then check the silicone tube to see whether it can produce water, especially if the water flow is normal.

Step 10

Turn on the power: connect the 220V power to the laser power and open the emergency stop, then the power is blocked to see if the power is normal. Press ESC twice and then press up-down-right-left on the Leetro control panel to see if the laser head can move usually.

Step 11

Connect the softdog to the computer, copy the data from the CD to the computer, use the data cable to connect the computer with the red card, and then install the software properly. Read more.

Step 12

Open the Lasercut icon on the desktop of the computer, and design a circle of approximately 40*40 mm, the processing method is cutting, the speed is 100, the power is 1 and then downloads in the machine. Move the laser head to the right place, then press “test” to see if the laser head can surround the edge. Whether it is normal, press “start” and start working.

I hope that the above steps can help eliminate your confusion about the installation of the CO2 laser engraving and cutting machine.

How to correctly install CO2 laser engraving and cutting machine?

This is a key point: the CO2 laser machine will work well only if you install the CO2 laser engraving and cutting machine correctly. Do not worry; this article will help you to know the correct installation process of the CO2 laser engraving and cutting machine. Let’s go with the following steps to install a CO2 laser machine:

Step 1

Remove the whole package; recover the machine such as wood, plastic film, etc. Be careful with of the nails.

Step 2

Now open the front door, the side door and remove all additional parts of the machine, such as water cooler, dust collector, air pump, laser tube, rotary etc. Please cut the tie on the X-axis belt and Y axis after opening the front door, get the CD and then move the laser head to the center of the work area by hand.

Step 3

The most vital step to install correctly a CO2 laser machine is to install the CO2 laser tube. Remove the laser tube from the package leisurely, and then put it in the socket of the laser tube on the back of the machine. If the laser tube has a protective plastic cover, cover the protective tape. If not, please cover enough waterproof tape. In the laser light, there is water behind the high-pressure end is water.

Step 4

Water cooler installation:  connect the water inlet and the water outlet of the water cooler with the water outlet and the water inlet of the machine by means of the silicone tube and then connect the air plugs.

Step 5

Installation of the air pump: connect the air outlet of the air pump with the air inlet of the laser cutting.

Step 6

The method of installation of the dust collector: connect the tire port of the dust collector with the telescopic tube of the laser machine.

Step 7

The installation of the floor: connect the security of the floor, find a cable and you must connect the machine to the floor. The other end connects the steel bar; it should be buried under the ground 1.5 meters. If it is in the humid place, the depth of the burial can be shallow.

Step 8

CO2 laser cutter should use the power with the 220V. If your local power is 220V, you can directly connect it. If not, you require an additional power transformer for the machine to change the power.

Step 9

First, supply power to the water cooler. Then check the silicone tube to see whether it can produce water, especially if the water flow is normal.

Step 10

Turn on the power: connect the 220V power to the laser power and open the emergency stop, then the power is blocked to see if the power is normal. Press ESC twice and then press up-down-right-left on the Leetro control panel to see if the laser head can move usually.

Step 11

Connect the softdog to the computer, copy the data from the CD to the computer, use the data cable to connect the computer with the red card, and then install the software properly.

Step 12

Open the Lasercut icon on the desktop of the computer, and design a circle of approximately 40*40 mm, the processing method is cutting, the speed is 100, the power is 1 and then downloads in the machine. Move the laser head to the right place, then press “test” to see if the laser head can surround the edge. Whether it is normal, press “start” and start working.

I hope that the above steps can help eliminate your confusion about the installation of the CO2 laser engraving and cutting machine.

Advanced Laser Cutting Techniques – Make Your Work Easier!

Laser cutting is a technology that uses this light to cut materials and is generally used for manufacturing applications in industries. Many fans together with small businesses and schools are starting to use this technology as well. Laser cutter aims to direct the high power output of the gleam by a computer to a material that must be cut. The material then, either by a gas jet, vaporizes or burns, leaving an edge that has a high quality surface finish. Industrial cutters are typically used to cut flat sheet materials and materials with pipes and structures. It has become a significant part of the manufacturing procedure. These are the part of the merits.

1. Holding the Work in Position and Without Contamination

One of the main benefits of using a laser machine is that the workpiece is kept in its correct position. This is all a merit that this process provides on mechanical cutting. The grip is placed precisely and is easier as well. The cuts made by the laser machine are very precise and do not need too much time. On the contrary, the total cutting technique has easier and the task is carried out in a much shorter time. Compared with conventional flash cutting machines, they do not have any direct contact with the workpiece so that there is no contagion of the material.

2. No Deformation and Is Versatile

In this cutting technique, the main advantages of using a laser machine include that, the heat to which the area is subjected is small. This benefits a lot since there is a reduction in the chances of the material warping. In most conventional processes, large amounts of heat are generated that convert materials into reports. The amount of energy used for this flash process is comparatively less than any other plasma cutting technology. It can be used to cut a large amount of materials such as certain metals, rubber, plastic, ceramics and wood. This is one of the most versatile processes for cutting or engraving complex designs into simple ones in a workpiece.

3. The Best Use of Space and Lower Mishaps

There are several manufacturing units that one could find, with space limitations. Therefore, installing such laser machines that use flashes may be a perfect idea. Actually, the reality is that machines have more than one gleam that is capable of doing a significant amount of work that is equivalent to the work done by some machines. As everything is controlled by computer programs, the amount of labor is considerably saved. Because this technique does not require any type of human intervention, except for trial runs and repairs, you can make sure that the number of injuries or accidents during work will be reduced.

4. The Efficiency Is Higher

The efficiency of the laser machine is very high and the replicas attained from the necessary design are ideal copies with each other. The holes with a small diameter that imply good edge quality and complex details in the section of the box, plate, tube, and sheet can be achieved rightly. The manufacturing cost is greatly reduced and is just ideal for cutting products that are lightweight metal. Check here.

Conclusion

If you need laser cutting for your home furniture, ceramics, plastic materials, and other items, you can contact a reputable and trustworthy laser cutting company. You can do this by searching the Internet and this would offer you a lot of information and you could decide which laser cutting company to choose, meeting your requirements and budget constraints.

Cleaning metal surfaces with a laser

Laser cutter desires steel fabricators to consider the utilization of a fiber content laser for surface planning, coloring removal, and surface cleaning applications. The business believes the nonabrasive method of cleaning is safer and much more environmentally friendly than mechanized and chemical substance cleaning methods.

Metal fabricators which may have painted and natural powder coating lines have to deal with the headaches of large pretreatment systems that want intense oversight to ensure the chemicals build a surface to that your paint or natural powder can properly adhere. Other fabricators may need to worry about organizing metal surfaces for welding, which requires the right power tool, abrasive, and a lot of elbow grease. Some retailers might have to decrease material or remove anodized surfaces prior to further processing. Many of these fabricators know that resources and competence are needed to obtain the clean surface necessary for the next step in the fabrication process.

Laser systems

The laser machine systems remove coatings, impurities, and residues by using high-energy dietary fiber laser resources, the same type of power source found in the company’s laser reducing and marking systems. Some of the power of the laser, electricity source would depend on the application form, but it can reach the kilowatt range if necessary.

The process is meant to replace the utilization of chemicals and abrasives to clean these metal floors. The fabricator places the part to be cleaned out in the School 1 enclosure and initiates a cleaning program. The equipment operator can choose to use a preinstalled cleaning structure or create a custom routine to meet a certain surface standards or throughput requirement. The operator can also modify a program to add multiple moves using different ideals for power, rate of recurrence, and swiftness on each laser machine move. A databases can store a large number of different cleaning jobs so that the operator doesn’t have to remember a cleaning job that was done previously.

The laser can be used to clean a number of metals, including metal, aluminum, stainless, and galvanized. It could even use reflective metals, such as brass and copper, and nonmetallic materials, such as plastics and silicone.

Laser cleaning capability

This laser machine cleaning capability is not limited to flat surfaces, according to company officers. Most laser systems have statically located cleaning minds, which restricts the laser cleaning capability to only the static course of the trajectory beam. It’s similar to a noon-time rays of the sun hitting a subject directly outrageous rather than making contact with other areas concealed from the sun’s 90-level positioning over the object. CleanTech fixed cleaning units are designed to clean those areas on 3-D items that are hard to reach.

Laser cleaning technology

This laser cleaning technology is not limited by a stand-alone, midsized product. It is available in a handheld device where the steel surface works as underneath of the laser chamber. A laser eliminates the impurities as the operator operates the hand held unit within the metal surface. This sort of a device can have a working envelope up to 4 by 4 inches wide.

The stationary parts can be made to be part of a production brand. An integrated particles and residue collection system can be contained as well to minimize manual laser machine cleaning.

 

Planning Rainy Day Fun

Planning Rainy Day Fun

When it rains, it pours but sometimes that’s not such a bad thing! A comfy, cozy, rainy day is the perfect excuse to stay in bed and binge watch some of your favorite movies. It’s also a great way to reconnect with friends! Gathering some of your close friends and enjoying a day in watching movies, reading magazines, and eating popcorn is a great way to pass the time. If you’re a responsible adult with a 9 to 5 job and you’re tired of all the constant stresses a rainy day but might a nice respite. Sleepover style parties aren’t just for teenagers! They’re also a great way for stressed out adults to get in touch with their inner child. Carving out some time for yourself and your friends is a great way to spend a rainy day.  Also look at bodor laser reviews as well as a way to what company to buy your laser from.  It may be a good choice and now is the time to review.

Now since you can’t predict the weather, planning a rainy day in with your closest girlfriends may have to happen on a day prior to the event. If you’ve got everything that you need for your rainy day in before it starts to rain is the best way to be prepared for whenever the skies open up. Springtime is the perfect time to stock up your house with provisions for your girl’s rainy day in. Make sure you have all of your favorite movies and don’t forget to get the favorite movies of some of your friends too. Movies are only half of the fun, dance parties are a great rainy day activity so you might want to create a playlist in advance. Stocking up on magazines, nail polish, and snacks is another key element to planning your rainy day in with the girls! The best place to go for snacks, nail polish, and magazines is Walgreens of course. They’ve got a wide selection and great deals.

Maybe you aren’t able to get all your friends together for a girl’s day in well there are several other rainy day activities to participate in. If you never have time to yourself a rainy day is the best time to catch up on self care. Taking a nice hot candle lit bath with the sound of rain in the background is an ideal way to spend an afternoon. Add some fun to your bath with the help of Lush bath bombs. With such a wide variety of bath bombs you can find the perfect match for you. Featuring fresh ingredients and intoxicating scents bath bombs add fun, relaxation, and invigoration to your bath. If you’re looking to do something a little more active with the family try an indoor treasure hunt. Treasure hunts are a great way to capture your children’s imaginations while having a lot of fun on a rainy day!

If you are able to invite your gal pals over for a rainy day filled with popcorn, movies, dancing, manicures, and gossip make sure they never forget their time with you. Creating little gift bags to commemorate your rainy day in is a super cute way to remember your perfect rainy day. Shopping at Lakeside Collection for personalized gifts is a super simple way to get one-of-a-kind commemorative gifts.  If you are in the market for a laser machine be sure to check out BBB reviews of Boss Laser.  You can get verified feedback unlike what most companies post on their own website.  

When the rain starts to pour remember, there’s so much in store!  

Activities to do on a Rainy Day

How to perfect your pick up lines

Using pick up lines can be fairly hit or miss when attempting to flirt with someone of either gender, no matter how slick you think you may be. There are a few rules to remember and tricks to try when deciding to employ a pick up line to increase your chances of success and reduce the risk of embarrassment.

It’s Best to Try the Honest Approach.

Instead of a pick up line, just try the honest approach. Most people respond much better to a simple “Hi, my name is _______, what’s your name?” than they do a cheesy, overused pick up line. It may seem counter intuitive, but the direct and straightforward approach is the best one, over all, and it makes you seem like less of a creep. Don’t you want to start out on a good foot instead of falling flat on your face with a pick up line that he or she may have heard a million times before? First impressions matter a lot, especially if you’re trying to meet a new romantic partner, and you only get one chance to make a good one so make it count. This could be a story you tell to your kids down the line and a funny pick up line may not be the wisdom you wish to impart on your future generations. Also, according to psychology, “trait perception” plays a large role in those first interactions. Since we are not able to see a list of traits from the people we interact with, you are forced to infer them from the actions the other person takes. Coming at somebody with a cheesy pick up line like “Do you wash your pants in Windex? Cause I can see myself in them” says more about you than you think it does… and not in any good way. See more.

If you are looking for a calling a laser company to investigate the quality of their laser cutters than you may think of a good line for getting the truth about their machines and support.  Check out Boss Laser reviews here.

Try the flattering approach.

If you want to use a pick up line, try just starting with something flattering. Be careful, though. There’s a thin line between sounding like a creep and saying something genuinely flattering. Try to stay away from anything too physical or personal. An exception to that is complimenting his or her smile, if they are in fact smiling. It’s best to stick to flattering his or her choice of drink or an item of clothing (think more shirt and less pants). Make sure that they know you are approaching them as a person and not as a body. Some pick up lines tend to sound like you’re only interested in getting to know their body and not the whole person and can be a huge turnoff. Approach someone genuinely and compliment them on something that sticks out. Don’t try too hard… people can see right through that and you come off as aggressive or a fraud.

Remember, pick up lines can be fun if you use them intelligently. A good pick up line is one that is genuine, funny and direct without being creepy or reducing the person to a body part. See more this site:  http://www.rainydaysandpajamas.com/cant-go-outside-to-play-no-problem/.

For beginners looking to buy a machine read reviews of Thunder Laser here.